"LoRa Setup" rev_17

/********* Pleasedontcode.com **********

    Pleasedontcode thanks you for automatic code generation! Enjoy your code!

    - Terms and Conditions:
    You have a non-exclusive, revocable, worldwide, royalty-free license
    for personal and commercial use. Attribution is optional; modifications
    are allowed, but you're responsible for code maintenance. We're not
    liable for any loss or damage. For full terms,
    please visit pleasedontcode.com/termsandconditions.

    - Project: "LoRa Setup"
    - Source Code compiled for: Arduino Uno
    - Source Code created on: 2024-11-29 23:09:25

********* Pleasedontcode.com **********/

/****** SYSTEM REQUIREMENTS *****/
/****** SYSTEM REQUIREMENT 1 *****/
    /* configure a lora gateway */
/****** SYSTEM REQUIREMENT 2 *****/
    /* send periodically a message to receiver. */
/****** END SYSTEM REQUIREMENTS *****/

/* START CODE */

/****** DEFINITION OF LIBRARIES *****/
#include <SPI.h>
#include <LoRa.h>   //https://github.com/sandeepmistry/arduino-LoRa

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);
void updateOutputs();
void sendLoRaMessage(const char* message);

/***** DEFINITION OF DIGITAL INPUT PINS *****/
const uint8_t module_SX127x_DIO0_PIN_D3     = 3;

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t module_SX127x_NRESET_PIN_D2       = 2;

/***** DEFINITION OF SPI PINS *****/
const uint8_t module_SX127x_SPI_PIN_MOSI_D11        = 11;
const uint8_t module_SX127x_SPI_PIN_MISO_D12        = 12;
const uint8_t module_SX127x_SPI_PIN_SCLK_D13        = 13;
const uint8_t module_SX127x_SPI_PIN_CS_D10      = 10;

/***** DEFINITION OF OUTPUT RAW VARIABLES *****/
/***** used to store raw data *****/
bool    module_SX127x_NRESET_PIN_D2_rawData     = 0;

/***** DEFINITION OF OUTPUT PHYSICAL VARIABLES *****/
/***** used to store data after characteristic curve transformation *****/
float   module_SX127x_NRESET_PIN_D2_phyData     = 0.0;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/

// Remove the instantiation of LoRa object here
// LoRaClass LoRa; // This line is removed

void setup(void)
{
    // put your setup code here, to run once:

    pinMode(module_SX127x_DIO0_PIN_D3,  INPUT);
    pinMode(module_SX127x_NRESET_PIN_D2,     OUTPUT);
    pinMode(module_SX127x_SPI_PIN_CS_D10,    OUTPUT);

    // start the SPI library:
    SPI.begin();

    // Initialize LoRa
    LoRa.setPins(module_SX127x_SPI_PIN_CS_D10, module_SX127x_NRESET_PIN_D2, module_SX127x_DIO0_PIN_D3);
    if (!LoRa.begin(915E6)) { // Set frequency to 915 MHz
        while (1); // if failed, do nothing
    }
}

void loop(void)
{
    // put your main code here, to run repeatedly:
    updateOutputs(); // Refresh output data

    // Send a message every 5 seconds
    sendLoRaMessage("Hello, LoRa!");
    delay(5000);
}

void updateOutputs()
{
    digitalWrite(module_SX127x_NRESET_PIN_D2, module_SX127x_NRESET_PIN_D2_rawData);
}

void sendLoRaMessage(const char* message)
{
    LoRa.beginPacket();
    LoRa.print(message);
    LoRa.endPacket();
}

/* END CODE */