EE BrightBox - Boot Log

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
ROMM
====
HELO
ZBSS
RAMM
====
Copyright (C) 2012 Arcadyan Technology.

SPIFLASH:
    JEDEC ID: 0xc22017, size: 8192KB
    block: 64KB(64), sector: 4KB(1024)

NVRAM(0) MAGIC checking passed!
NVRAM(0) CRC checking passed!
total 5 of NVRAM(0) entries loaded

NVRAM(1) MAGIC checking passed!
NVRAM(1) CRC checking passed!
total 7 of NVRAM(1) entries loaded

BOOTLOADER version 1.0.10 for BrightBox
Build Date: Fri Sep 21 03:00:26 2012 (brian_chang@buildbed)

Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Memory Test Passed!
Total Memory: 67108864 bytes (64MB)
HW Version: 01
Board IP address        192.168.1.1
Board IP netmask        255.255.255.0
Gateway IP address      0.0.0.0
Server IP address       192.168.1.99
Boot image (1 or 2)     1
MAC address number      1
MAC address base        88-03-55-19-7F-EB
*** Press any key to stop auto run (3 seconds) ***
Auto run second count down: 0
Loading primary image ...
Finished loading 8257536 bytes
DATE    : Fri Sep 21 03:00:26 2012
VER     : v0.09.94.0006
CRC     : CA7C2EC6
Code Address: 0x80002000, Entry Address: 0x801d8550
Decompression OK!
Entry at 0x801d8550
Starting program at 0x801d8550
Linux version 2.6.30 (brian_chang@buildbed) (gcc version 4.1.2) #1 Fri Sep 21 02:51:02 CST 2012
Detected Broadcom 0x6328 CPU revision 10b0
CPU frequency is 320 MHz
64MB of RAM installed
registering 32 GPIOs
console [early0] enabled
CPU revision is: 0002a075 (Broadcom BCM63281)
board_bcm9632x: board name: AR7516AAW
Determined physical RAM map:
 memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8024bb30, node_mem_map 81000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro rootfstype=squashfs
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:80
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61368k/64512k available (1912k kernel code, 3124k reserved, 436k data, 120k init, 0k highmem)
Calibrating delay loop... 318.46 BogoMIPS (lpj=159232)
Mount-cache hash table entries: 512
--Kernel Config--
  SMP=0
  PREEMPT=0
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
net_namespace: 536 bytes
/proc/net/netfilter/nf_cli_bw_mon created
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D0 D3hot
pci 0000:00:00.0: PME# disabled
pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:00.0: PCI bridge, secondary bus 0000:01
pci 0000:00:00.0:   IO window: disabled
pci 0000:00:00.0:   MEM window: 0x10f00000-0x10ffffff
pci 0000:00:00.0:   PREFETCH window: disabled
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:00.0 to 64
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Sep 21 2012 02:49:54 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
Total # RxBds=848
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized

squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 119
io scheduler noop registered (default)
PCI: Setting latency timer of device 0000:00:00.0 to 64
aer 0000:00:00.0:pcie02: service driver aer loaded
bcm632x-uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm632x-uart
console handover: boot [early0] -> real [ttyS0]
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
m25p80 spi0.0: mx25l6405d (8192 Kbytes)
Creating 6 MTD partitions on "spi0.0":
0x00000000e000-0x00000000f000 : "manuf"
0x00000000f000-0x000000010000 : "nvram"
0x000000110000-0x0000007f0000 : "rootfs"
0x000000010000-0x0000007f0000 : "priimg"
0x0000007f0000-0x000000800000 : "pricfg"
0x000000000000-0x00000000e000 : "bootldr"
bcm632x-hsspi bcm632x-hsspi.0:  at 0xb0001000 (irq 37, FIFOs size 510) v1.0
Registered led device: dsl:sync
Registered led device: dsl:data
Registered led device: wps:green
Registered led device: sys:a
Registered led device: sys:b
Registered led device: sys:c
Registered led device: sys:d
GACT probability on
u32 classifier
    Actions configured
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
Initializing MCPD Module
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 120k freed
gpio-buttons driver version 0.1.2
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.4.1
arc_oshal: module license 'Propritary' taints kernel.
Disabling lock debugging due to kernel taint

oshal_init(1066) DRV: Created Successfully

ARC_KERNEL_OSIX_init(396) DRV: Created Successfully
Broadcom Logger v0.1 Sep 21 2012 02:51:21
Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v2.2 Sep 21 2012 02:51:23 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Sep 21 2012 02:51:23
Broadcom BCM6328B0 Ethernet Network Device v0.1 Sep 21 2012 02:51:25
ETH Init: Ch:0 - 180 tx BDs at 0xa3946000
ETH Init: Ch:0 - 400 rx BDs at 0xa3a21000
bcm632x-dg: register bcmsw
eth0: MAC Address: 88:03:55:19:7F:EB
eth1: MAC Address: 88:03:55:19:7F:EB
eth2: MAC Address: 88:03:55:19:7F:EB
eth3: MAC Address: 88:03:55:19:7F:EB
Broadcom 802.1Q VLAN Interface, v0.1
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.4 Sep 21 2012 02:51:33
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom Power Management v0.1 Sep 21 2012 02:52:42
Broadcom WLAN configuration service start
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
wl: passivemode=1
wl: napimode=0
wl: allocskbmode=1
wl:force using embedded data
wlc_bmac_attach(2582): BpGetWirelessFlags NIY!
wl0: Broadcom BCMa8dc 802.11 Wireless Controller 5.100.96.0.cpe4.10L01a.8
bcm632x-dg: register wl0
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
IMQ driver loaded successfully.
        Hooking IMQ after NAT on PREROUTING.
        Hooking IMQ before NAT on POSTROUTING.

Osix_service_sys_cmd_thread_main[1302]: Osix Wait for Batch System Comand Processing...
Osix Thread service system command started successfully !
ramdisk/etc/config/
ramdisk/etc/config/glbcfg.save
MHDL_DB_WLAN_Init_Setting[118]
MHDL_DB_LAN_Init_Setting[525]
Password for 'admin' changed
BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
BcmAdsl_Initialize(202): BpGetRj11InnerOuterPairGpios NIY
pSdramPHY=0xA3FFFFF8, 0xD1AF908B 0xD183938B
*** PhySdramSize got adjusted: 0x82CDC => 0x98878 ***
AdslCoreSharedMemInit: shareMemAvailable=423776
AdslCoreHwReset:  pLocSbSta=83120000 bkupThreshold=1600
AdslCoreHwReset:  AdslOemDataAddr = 0xA3F77D28
EXECUTE "/bin/util_xdsl_cli mode auto"
BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
EXECUTE "/bin/util_xdsl_cli bitswap enable"
BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
EXECUTE "/bin/util_xdsl_cli sra enable"
BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
devCtl_xtmInitiaXTM Init: Ch:0 - 400 rx BDs at 0xa3bc5000
lize(174): devCtXTM Init: Ch:1 - 16 rx BDs at 0xa29b0780
l_getSdramSize NIY!
WAN Type is ADSL
Success
Success
Success
Success
Success
Success
 Power ON stage, no need to delete interface in advance.
ioctl failed. check if wl0.1 exists
MHDL_DB_SYS_DNS_UPDATE_RESOLV_CONF[1046]: cmd_buf (cp /tmp/tmpResolv_536.conf /etc/resolv.conf)
dhcp IP compare: old ()  vs new (192.168.69.69).
 dhcp lease time compare: old (00000000)  vs new (0002A300).
mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE)
dhcp IP compare: old ()  vs new (192.168.2.1).
 dhcp lease time compare: old (00000000)  vs new (0000A8C0).
mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE)
Restart Level is BR0_IPCHANGED
BR0 IP Changed
dhcp IP compare: old ()  vs new (192.168.3.1).
 dhcp lease time compare: old (00000000)  vs new (0000A8C0).
mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE)
ioctl failed. check if wl0.1 exists
 Initializing WAN
XTM driver returns Not Found Error

bcmxtmrt: MAC address: 88 03 55 19 7f ed
[DoCreateDeviceReq.2998]: register_netdev
[DoCreateDeviceReq.3000]: register_netdev done
/bin/bcm_atmctl operate conn --add 1.0.38 aal5 vcmux_pppoa 1MHDL_DB_SYS_STOP_UPNPD[1322]: cmd (killall arc_upnp)
killall: arc_upnp: no process killed
MHDL_DB_SYS_RESTART_UPNPD[1306]: cmd_buf: /usr/sbin/arc_upnp &
Success
Success
Success
Success
Success
ioctl failed. check if wl0.1 exists
modprobe: can't open 'modules.dep': No such file or directory
The kernel doesn't support the ebtables 'nat' table.
iptables v1.4.8: Couldn't find target `QOSUP'

Try `iptables -h' or 'iptables --help' for more information.
ioctl failed. check if wl0.1 exists
iptables v1.4.8: Couldn't find target `QOSUP'

Try `iptables -h' or 'iptables --help' for more information.
net.netfilter.nf_conntrack_acct = 1
ioctl failed. check if wl0.1 exists
RTNETLINK answers: Invalid argument
Pre-init before any Application was started.
killall: dyndns: no process killed
killall: tzoupdate: no process killed
start httpd
CLOCK_MONOTONIC, resolution=0.999848
System clock_res=999848, clock_hz=1000
config_httpd(517) LAN IP Address (192.168.69.69)
config_httpd(526) LAN IP Mask (255.255.255.0)
httpd: after config_httpd()
httpd: listen at 192.168.69.69:5438
[HTTPD] httpd_main(): Not the 1st httpd_main task
Success
Success
SSDP_SetRCVSocket(217): Recv SsdpSock 14
Success
Success
QueryEthernetLinkStatus[115]: WAN Interface Name (NULL)
Port Number: eth3, PortStatus: 0
Success
 1 Jan 00:00:26 sntp[966]: kod_init_kod_db(): Cannot open KoD db file /var/db/ntp-kod
 1 Jan 00:00:26 sntp[966]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
ioctl failed. check if wl0.1 exists
killall: bcm_mcpd: no process killed
HTTPD: main(1480)
lease_init[65]:  /etc/udhcpd/udhcpd_001.leases !
main(1572): I am child for HTTPD SVR 2
main(1584): Start HTTPD SVR 0
Restart Level is BR1_IPCHANGED
BR1 IP Changed
killall: bcm_mcpd: no process killed
ioctl failed. check if wl0.1 exists
lease_init[65]:  /etc/udhcpd/udhcpd_002.leases !
Restart Level is BR2_IPCHANGED
BR2 IP Changed
please assign value for wl0.1_ssid
please assign value for wl0.2_ssid
killall: bcm_mcpd: no process killed
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
rmmod: can't unload 'nf_nat_pt': unknown symbol in module, or unknown parameter
killall: urlfilterd: no process killed
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
conntrack v1.0.0 (conntrack-tools): connection tracking table has been emptied.
conntrack v1.0.0 (conntrack-tools): expectation table has been emptied.
please assign value for wps_aplockdown_count
ioctl failed. check if wl0.1 exists
ioctl failed. check if wl0.1 exists
please assign value for wl0_radius_key
please assign value for wl0_nas_id
 1 Jan 00:00:50 sntp[2721]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
please assign value for wl0.1_wpa_psk
please assign value for wl0.2_wpa_psk
ioctl failed. check if wl0.1 exists
start WLAN manager
WLmngr Daemon is running
ifconfig: wl0.1: error fetching interface information: Device not found
ifconfig: wl0.2: error fetching interface information: Device not found
wlevt_init@157: opened loopback socket 6
wlevt is ready for new msg...
nvram_commit NIY!
ifconfig: wl0.1: error fetching interface information: Device not found
ifconfig: wl0.2: error fetching interface information: Device not found
ioctl failed. check if wl0.1 exists
>>>>>Start Auto Channel search !!! >>>>>
Setting SSID: "EE-BrightBox-7s6r9p"
Setting SSID: "ar7516aaw-guest"
Setting SSID: "ar7516aaw-guest2"
chanspec 0x2b0b selected
bcm_wlctl: Unsupported
bcm_wlctl: Not Permitted
bcm_wlctl: Undefined error
nvram_commit NIY!
LLTD daemon is ready to run
EAP daemon is ready to run
NAS daemon is ready to run
wlmngr_startWsc(1127): wait for WPSUI message timeout!
dalQos_setDefaultWlQueuesLock NIY!
dalQos_setDefaultWlQueuesLock NIY!
dalQos_setDefaultWlQueuesLock NIY!
read/write to TR69 configuration NIY!
Starting to init bandwidth contrl of wifi!!
/sbin/tctrl qdisc del dev wl0 ingress 2>/dev/null
/usr/sbin/ebtables -X wl0_egress 2>/dev/null
iptables: No chain/target/match by that name.
/sbin/tctrl qdisc del dev wl0 root 2>/dev/null
/usr/sbin/ebtables -X wl0_ingress 2>/dev/null
/sbin/tctrl qdisc del dev wl0.1 ingress 2>/dev/null
/usr/sbin/ebtables -X wl0.1_egress 2>/dev/null
/sbin/tctrl qdisc del dev wl0.1 root 2>/dev/null
/usr/sbin/ebtables -X wl0.1_ingress 2>/dev/null
/sbin/tctrl qdisc del dev wl0.2 ingress 2>/dev/null
/usr/sbin/ebtables -X wl0.2_egress 2>/dev/null
/sbin/tctrl qdisc del dev wl0.2 root 2>/dev/null
/usr/sbin/ebtables -X wl0.2_ingress 2>/dev/null
start mcpd
start USB service
Password for 'user' changed
 1 Jan 00:01:14 sntp[3549]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
bcm632x-usb-ohci bcm632x-usb-ohci.0: init err (c8300000 0000)
bcm632x-usb-ohci bcm632x-usb-ohci.0: startup error -79
bcm632x-usb-ohci: probe of bcm632x-usb-ohci.0 failed with error -79
action name is add
product name is 1d6b/2/206
Driver 'sd' needs updating - please use bus_type methods
start UMTS service
action name is add
product name is 1d6b/2/206
start Power-Management service
Host MIPS Clock divider pwrsaving is enabled
DDR Self Refresh pwrsaving is enabled
 System Start with Normal Phase
 1 Jan 00:01:42 sntp[3699]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
 1 Jan 00:02:06 sntp[3741]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
 1 Jan 00:02:30 sntp[3794]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
 1 Jan 00:02:55 sntp[3836]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)
 1 Jan 00:03:19 sntp[3878]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known
Unable to resolve hostname(s)