eldk-5.0-qte-sdk-armv7a-1

Texas Instruments X-Loader 1.47 (Mar 24 2011 - 15:54:49)
Starting X-loader on MMC
Reading boot sector

200544 Bytes Read from MMC
Starting OS Bootloader from MMC...
Starting OS Bootloader...


U-Boot 2010.06-rc1 (Jan 28 2011 - 14:26:50)

OMAP34xx/35xx-GP ES1.0, CPU-OPP2 L3-165MHz
TAM3517 TWISTER Board + LPDDR/NAND
I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Customer/Vender : TechNexion
Project/Board   : tam3517
Sequence Number : 1052000000000092
revision        : TN15 1.0
eth0 addr      : 00:1F:7B:15:01:6C
eth1 addr      : 00:1F:7B:15:01:6D
eth2 addr      : 00:1F:7B:15:01:6E
eth3 addr      : 00:1F:7B:15:01:6F
Die ID #45020000000000000155dc140501f00e
Net:   Ethernet PHY: GENERIC @ 0x00
DaVinci EMAC, smc911x-0
Hit any key to stop autoboot:  0
TAM3517 # printe mmcargs
mmcargs=run def_sys_mode;run def_disp_mode;setenv bootargs mem=${memsize} mpurate=${mpurate} console=${console} omapfb.vram=0:${vram_size} eth0addr=${eth0addr} eth1addr=${eth1addr} eth2addr=${eth2addr} eth3addr=${eth3addr} ${android_args} ${sys_mode} ${board_info} ${auto_run} omapdss.def_disp=${def_disp} ${disp_mode} ${touch_calibration} mtdparts=${nandparts} root=/dev/mmcblk0p${rootfsmmc} rw rootfstype=ext3 rootwait
TAM3517 # sete rootfsmmc 3
TAM3517 # run bootmmc
## Error: "bootmmc" not defined
TAM3517 # run mmcboot
mmc1 is available
reading uImage

2914612 bytes read
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   Linux-2.6.32
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2914548 Bytes = 2.8 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.32 (rber@yocto-vm-1) (gcc version 4.5.1 (GCC) ) #1 Wed May 18 20:32:17 EEST 2011
CPU: ARMv7 Processor [411fc087] revision 7 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: TAM3517 EVM
Memory policy: ECC disabled, Data cache writeback
AM3517 ES1.0 (l2cache iva sgx neon isp )
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
Reserving 10485760 bytes SDRAM for VRAM
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: mem=256M mpurate=600 console=ttyS0,115200n8 omapfb.vram=0:10M eth0addr=00:1F:7B:15:01:6C eth1addr=00:1F:7B:15:01:6D eth2addr=00:1F:7B:15:01:6E eth3addr=00:1F:7B:15:01:6F SYSTEM=2 CUSTOMER=TechNexion PRODUCT=tam3517 ID=1052000000000092 BOARD_TN=15 BOARD_REVISION_MAJOR=1 BOARD_REVISION_FIXED=0 omapdss.def_disp=lcd panel-generic.disp_timings=33300,800/210/46/1,480/22/23/1,24 ads7846.calibration=-13943,25,54444704,-124,-9117,34403056,65536 ads7846.swap_left_right=1 ads7846.swap_top_down=1 ads7846.x_min=180 ads7846.y_min=330 ads7846.x_max=3900 ads7846.y_max=3800 mtdparts=omap2-nand.0:512k(xloader),1024k(uboot),512k(params),6m(kernel),-(rootfs) root=/dev/mmcblk0p3 rw rootfstype=ext3 rootwait
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 243584KB available (5120K code, 384K data, 160K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:368
Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
GPMC revision 5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
Total of 96 interrupts on 1 active controller
OMAP GPIO hardware version 2.5
OMAP clockevent source: GPTIMER1 at 32768 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 499.92 BogoMIPS (lpj=1949696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
tmpfs: No value for mount option 'mode'
devtmpfs: initialized
regulator: core version 0.5
NET: Registered protocol family 16
mux: Could not set signal i2c2_scl
mux: Could not set signal i2c2_sda
mux: Could not set signal i2c3_scl
mux: Could not set signal i2c3_sda
Display initialized successfully
Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
OMAP DMA hardware revision 4.0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 400 kHz
regulator: VDCDC1: 1200 mV normal
regulator: VDCDC2: 3300 mV normal
regulator: VDCDC3: 1800 mV normal
regulator: LDO1: 1800 mV normal
regulator: LDO2: 3300 mV normal
i2c_omap i2c_omap.2: bus 2 rev3.12 at 400 kHz
i2c_omap i2c_omap.3: bus 3 rev3.12 at 400 kHz
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource 32k_counter
musb_hdrc: version 6.0, cppi4.1-dma, host, debug=0
AM3517 OTG revision 4ea41001, PHY f0036e2, control 00
musb_hdrc: USB Host mode controller at d0810000 using DMA, IRQ 71
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.32 musb-hcd
usb usb1: SerialNumber: musb_hdrc
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
AM3517  Linux PSP version 03.00.01.06 (TAM3517)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 476
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
OMAP DSS rev 2.0
OMAP DISPC rev 3.0
OMAP VENC rev 2
OMAP DSI rev 1.0
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
console [ttyS0] enabled
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
brd: module loaded
loop: module loaded
at24 1-0050: 256 byte 24c02 EEPROM (writable)
at24 2-0050: 256 byte 24c02 EEPROM (writable)
SCSI Media Changer driver v0.25
omap2-nand driver initializing
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bit)
5 cmdlinepart partitions found on MTD device omap2-nand.0
Creating 5 MTD partitions on "omap2-nand.0":
0x000000000000-0x000000080000 : "xloader"
0x000000080000-0x000000180000 : "uboot"
0x000000180000-0x000000200000 : "params"
0x000000200000-0x000000800000 : "kernel"
0x000000800000-0x000010000000 : "rootfs"
vcan: Virtual CAN interface driver
CAN device driver interface
TI High End CAN Controller Driver 0.7
ti_hecc ti_hecc.1: device registered (reg_base=d08e0000, irq=24)
smsc911x: Driver version 2008-10-21.
smsc911x-mdio: probed
eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
net eth0: MAC Address: 00:1f:7b:15:01:6d
usbcore: registered new interface driver cdc_ether
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 2
ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OMAP-EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
usb usb2: SerialNumber: ehci-omap.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
mice: PS/2 mouse device common for all mice
ads7846 spi1.0: touchscreen, irq 296
input: ADS7846 Touchscreen as /devices/platform/omap2_mcspi.1/spi1.0/input/input0
using rtc device, ds1307, for alarms
rtc-ds1307 3-0068: rtc core: registered ds1307 as rtc0
rtc-ds1307 3-0068: 56 bytes nvram
i2c /dev entries driver
Linux video capture interface: v2.00
OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: Broadcom Blutonium firmware driver ver 1.2
usbcore: registered new interface driver bcm203x
Bluetooth: Digianswer Bluetooth USB driver ver 0.10
usbcore: registered new interface driver bpa10x
Bluetooth: BlueFRITZ! USB driver ver 1.2
usbcore: registered new interface driver bfusb
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
Registered led device: status
omap_pwm_led omap_pwm_led.1: OMAP PWM LED (lcd-backlight) at GP timer 9/0
Registered led device: lcd-backlight
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.21.
usbcore: registered new interface driver snd-usb-audio
No device for DAI tlv320aic23
No device for DAI omap-mcbsp-dai-0
No device for DAI omap-mcbsp-dai-1
No device for DAI omap-mcbsp-dai-2
No device for DAI omap-mcbsp-dai-3
No device for DAI omap-mcbsp-dai-4
TAM3517 EVM SoC init
AIC23 Audio Codec 0.1
asoc: tlv320aic23 <-> omap-mcbsp-dai-0 mapping ok
ALSA device list:
  #0: tam3517 (tlv320aic23)
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
Power Management for TI OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1
usb 2-1: new high speed USB device using ehci-omap and address 2
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new high speed SDHC card at address 0001
mmcblk0: mmc0:0001 00000 7.60 GiB
 mmcblk0: p1 p2 p3
Console: switching to colour frame buffer device 100x30
regulator_init_complete: incomplete constraints, leaving LDO2 on
regulator_init_complete: incomplete constraints, leaving LDO1 on
emac-mii: probed
rtc-ds1307 3-0068: setting system clock to 2011-05-21 12:14:59 UTC (1305980099)
usb 2-1: New USB device found, idVendor=05e3, idProduct=0608
usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-1: Product: USB2.0 Hub
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
kjournald starting.  Commit interval 5 seconds
EXT3-fs (mmcblk0p3): warning: maximal mount count reached, running e2fsck is recommended
EXT3-fs (mmcblk0p3): using internal journal
EXT3-fs (mmcblk0p3): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) on device 179:3.
devtmpfs: mounted
Freeing init memory: 160K
INIT: version 2.88 booting
Starting udevudev[626]: starting version 164

usb 2-1.1: new high speed USB device using ehci-omap and address 3
usb 2-1.1: New USB device found, idVendor=05e3, idProduct=0718
usb 2-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
usb 2-1.1: Product: USB Storage
usb 2-1.1: SerialNumber: 000000000033
scsi0 : usb-storage 2-1.1:1.0
Configuring network interfaces... done.
Starting portmap daemon...
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting Distributed Compiler Daemon: distcc.
Starting syslogd/klogd: done
 * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon                       [ ok ]
Starting tcf-agent: OK
umount: /mnt/.psplash: device is busy.
        (In some cases useful info about processes that use
         the device is found by lsof(8) or fuser(1))

EDLK (Built by Poky 5.0) 5.0 armv7a ttyS0

armv7a login: scsi 0:0:0:0: Direct-Access     USB TO I DE/SATA Device   0015 PQ: 0 ANSI: 0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Attached SCSI disk
FAT: unable to read boot sector

EDLK (Built by Poky 5.0) 5.0 armv7a ttyS0

armv7a login: root