Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- ROM VER: 1.1.4
- CFG 05
- DDR autotuning Rev 0.3ff
- DDR size from 0xa0000000 - 0xa3ffffff
- DDR check ok... start booting...
- U-Boot 2010.06-LANTIQ-v-2.0.40-svn4469 (Aug 28 2013 - 09:28:56)
- CLOCK CPU 500M RAM 250M
- DRAM: 64 MiB
- Using default environment
- In: serial
- Out: serial
- Err: serial
- Net: Internal phy(GE) firmware version: 0x8434
- vr9 Switch8192 KiB W25Q64 at 0:3 is now current device
- Type "run flash_nfs" to mount root filesystem over NFS
- Hit any key to stop autoboot: 1 0
- 8192 KiB W25Q64 at 0:3 is now current device
- 8192 KiB W25Q64 at 0:3 is now current device
- Uncompressing ...
- Starting kernel ...
- Lantiq xDSL CPE VR9
- mips_hpt_frequency = 250000000, counter_resolution = 2
- Linux version 2.6.32.32 (swd@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #16 Wed Aug 28 09:30:48 CST 2013
- phym = 04000000, mem = 04000000, max_pfn = 00004000
- Reserving memory for CP1 @0xa4000000, size 0x00000000
- CPU revision is: 00019556 (MIPS 34Kc)
- Determined physical RAM map:
- User-defined physical RAM map:
- memory: 04000000 @ 00000000 (usable)
- Initrd not found or empty - disabling initrd
- Zone PFN ranges:
- Normal 0x00000000 -> 0x00004000
- Movable zone start PFN for each node
- early_node_map[1] active PFN ranges
- 0: 0x00000000 -> 0x00004000
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
- Kernel command line: root=/dev/mtdblock2 rw rootfstype=squashfs ip=192.168.1.1:192.168.1.2::::eth0:on console=ttyS0,115200 ethaddr=AC:9A:96:F0:28:39 phym=64M mem=64M panic=1 mtdparts=ifx_sflash:128k(boot),1280k(kernel),6528k(rootfs),64k(config),64k(romfile),64k(rom),64k(radio) init=/sbin/init ethwan=
- PID hash table entries: 256 (order: -2, 1024 bytes)
- Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
- Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
- Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
- Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
- Writing ErrCtl register=00011240
- Readback ErrCtl register=00011240
- Memory: 60632k/65536k available (2855k kernel code, 4832k reserved, 820k data, 184k init, 0k highmem)
- Hierarchical RCU implementation.
- NR_IRQS:185
- Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH
- console [ttyS0] enabled
- Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- Lantiq PCIe Root Complex driver, version 1.5.3, (c) 2001-2011 Lantiq Deutschland GmbH
- bio: create slab <bio-0> at 0
- ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
- pci 0000:00:00.0: PME# supported from D0 D3hot
- pci 0000:00:00.0: PME# disabled
- pci 0000:01:00.0: PME# supported from D0 D1 D3hot
- pci 0000:01:00.0: PME# disabled
- pci 0000:00:00.0: PCI bridge, secondary bus 0000:01
- pci 0000:00:00.0: IO window: disabled
- pci 0000:00:00.0: MEM window: 0x1c000000-0x1c0fffff
- pci 0000:00:00.0: PREFETCH window: 0x1c100000-0x1c1fffff
- NET: Registered protocol family 8
- NET: Registered protocol family 20
- Switching to clocksource MIPS
- NET: Registered protocol family 2
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 2048 (order: 2, 16384 bytes)
- TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
- TCP: Hash tables configured (established 2048 bind 2048)
- TCP reno registered
- NET: Registered protocol family 1
- gptu: totally 6 16-bit timers/counters
- gptu: misc_register on minor 63
- gptu: succeeded to request irq 118
- gptu: succeeded to request irq 119
- gptu: succeeded to request irq 120
- gptu: succeeded to request irq 121
- gptu: succeeded to request irq 122
- gptu: succeeded to request irq 123
- IFX DMA driver, version ifxmips_dma_core.c:v1.0.17
- ,(c)2009 Infineon Technologies AG
- Lantiq CGU driver, version 1.1.27, (c) 2001-2011 Lantiq Deutschland GmbH
- vpe1_mem = 0
- Wired TLB entries for Linux read_c0_wired() = 0
- squashfs: version 4.0 (2009/01/31) Phillip Lougher
- Registering mini_fo version $Id$
- fuse init (API version 7.13)
- msgmni has been set to 118
- Line: 127, function: deu_init
- DMA Referenced PAGE_SIZE = 4096
- Infineon Technologies DEU driver version 2.0.0
- IFX DEU DES initialized (multiblock) (DMA).
- IFX DEU AES initialized (multiblock) (DMA).
- IFX DEU ARC4 initialized (multiblock) (DMA).
- IFX DEU SHA1 initialized (DMA).
- IFX DEU MD5 initialized (DMA).
- IFX DEU SHA1_HMAC initialized (DMA).
- IFX DEU MD5_HMAC initialized (DMA).
- io scheduler noop registered (default)
- ifx_pmu_init: Major 252
- Lantiq PMU driver, version 1.2.2, (c) 2001-2011 Lantiq Deutschland GmbH
- Lantiq GPIO driver, version 1.2.14, (c) 2001-2011 Lantiq Deutschland GmbH
- Infineon Technologies RCU driver version 1.0.8
- Lantiq LED Controller driver, version 1.0.6, (c) 2001-2011 Lantiq Deutschland GmbH
- MEI CPE Driver, Version 1.2.0
- (c) Copyright 2009, Infineon Technologies AG
- ### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
- ttyS0 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC
- Register ASC (UART) to PMCU.
- Lantiq ASC (UART) driver, version 1.0.9, (c) 2001-2011 Lantiq Deutschland GmbH
- brd: module loaded
- loop: module loaded
- Lantiq SSC driver, version 2.2.6, (c) 2001-2011 Lantiq Deutschland GmbH
- Register flash device:flash0
- 7 cmdlinepart partitions found on MTD device ifx_sflash
- Creating 7 MTD partitions on "ifx_sflash":
- 0x000000000000-0x000000020000 : "boot"
- 0x000000020000-0x000000160000 : "kernel"
- 0x000000160000-0x0000007c0000 : "rootfs"
- mtd: partition "rootfs" set to be root filesystem
- 0x0000007c0000-0x0000007d0000 : "config"
- 0x0000007d0000-0x0000007e0000 : "romfile"
- 0x0000007e0000-0x0000007f0000 : "rom"
- 0x0000007f0000-0x000000800000 : "radio"
- Lantiq SPI flash driver, version 1.1.9, (c) 2001-2011 Lantiq Deutschland GmbH
- ifxmips_gpio: Pin ID 10 (port 0, pin 10) has been reserved by module SFLASH from kernel module!
- ifx_dataflash_init status error 255
- PPP generic driver version 2.4.2
- NET: Registered protocol family 24
- IFX SWITCH API, Version 1.1.7.2
- SWAPI: Registered character device [switch_api] with major no [81]
- Switch API: PCE MicroCode loaded !!
- Init IFX_ETHSW_Switch_API_procModule successfully.
- Switch Auto Polling value = 0
- GPHY FW load for A2x !!
- GPHY FIRMWARE LOAD SUCCESSFULLY AT ADDR : 400000
- IFX GPHY driver GE Mode, version ifxmips_vr9_gphy: V0.9 - Firmware: 8434
- Registered led device: broadband_led
- Registered led device: internet_led
- Registered led device: usb1_link_led
- Registered led device: usb2_link_led
- Lantiq LED driver, version 1.0.17, (c) 2001-2011 Lantiq Deutschland GmbH
- Mirror/redirect action on
- u32 classifier
- Actions configured
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (948 buckets, 5120 max)
- CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
- nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
- sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
- GRE over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- TCP cubic registered
- NET: Registered protocol family 10
- ip6_tables: (C) 2000-2006 Netfilter Core Team
- IPv6 over IPv4 tunneling driver
- NET: Registered protocol family 17
- NET: Registered protocol family 15
- Bridge firewalling registered
- Ebtables v2.0 registered
- NET: Registered protocol family 8
- atmpvc_init() failed with -17
- KOAM is loaded successfully.
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- Freeing unused kernel memory: 184k freed
- starting pid 187, tty '': '/etc/init.d/rcS'
- SCSI subsystem initialized
- usbcore: registered new interface driver usbfs
- usbcore: registered new interface driver hub
- usbcore: registered new device driver usb
- Initializing USB Mass Storage driver...
- usbcore: registered new interface driver usb-storage
- USB Mass Storage support registered.
- IFXUSB: ifxusb_hcd: version 3.2 B120208
- Chip Version :0002 BurstSize=4
- IFXUSB: USB core #0 soft-reset
- IFXUSB: USB core #0 soft-reset
- ifxusb_hcd ifxusb_hcd: IFX USB Controller
- ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
- ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000
- IFXUSB: Init: Power Port (0)
- hotplug, argusb usb1: configuration #1 chosen from 1 choice
- s:usb
- hotplug, args:usb
- .....pidhub 1-0:1.0: USB hub found
- hub 1-0:1.0: 1 port detected
- 228: wait the running hotplug to end itself.......
- IFXUSB: USB core #1 soft-reset
- IFXUSB: USB core #1 soft-reset
- ifxusb_hcd ifxusb_hcd: IFX USB Controller
- ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
- ifxusb_hcd ifxusb_hcd: irq 83, io mem 0xbe106000
- IFXUSB: Init: Power Port (0)
- hotplug, args:uusb usb2: configuration #1 chosen from 1 choice
- sb
- hotplug, argshub 2-0:1.0: USB hub found
- hub 2-0:1.0: 1 port detected
- :usb
- Please press Enter to activate this console. .....pid 228: wait the running hotplug to end itself.......
- [ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
- [ dm_loadCfg ] 2252: software version is not match, in config, version = 0
- [ dm_readFile ] 2042: can not open xml file /var/tmp/pc/default_config.xml!, about to open file /etc/default_config.xml
- [ parseConfigNode ] 521: Meet unrecognized object node "PhDDNSCfg", skip the node
- [ parseConfigNode ] 526: Meet unrecognized parameter node "PhDDNSCfg", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "X_TPLINK_MultiSSID", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "QueueManagement", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "X_TPLINK_IPTVCfg", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "VoiceService", skip the node
- [ parseConfigNode ] 526: Meet unrecognized parameter node "VoiceService", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "X_TPLINK_SpeedDialCfg", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "X_TPLINK_MultiIspDialPlan", skip the node
- [ parseConfigNode ] 521: Meet unrecognized object node "X_TPLINK_CallLogCfg", skip the node
- Loading A5 (MII0/1 + ATM) driver ...... MAC-0: e8-94-f6-0f-4d-50
- MAC-1: e8-94-f6-0f-4d-51
- Succeeded!
- PPE datapath driver info:
- Version ID: 64.3.7.1.0.1.4
- Family : VR9
- DR Type : Normal Data Path | Indirect-Fast Path
- Interface : MII0 | MII1 | ATM
- Mode : Routing
- Release : 0.1.4
- PPE firmware info:
- Version ID: 7.2.4.6.2.0
- Family : VR9
- FW Type : Acceleration
- Interface : MII0/1 + ATM
- Mode : Bridging + IPv4 Routing
- Release : 2.0
- IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
- Lantiq CPE API Driver version: DSL CPE API V4.11.4
- Predefined debug level: 3
- ifx_ppa_api: module license 'unspecified' taints kernel.
- Disabling lock debugging due to kernel taint
- .....pid 228: wait the running hotplug to end itself.......
- PPA API --- init successfully
- ifx_ppa_init - init succeeded
- sendto: No such file or directory
- send 2001 error 244, -1
- ioctl: No such device
- device eth0 entered promiscuous mode
- br0: port 1(eth0) entering forwarding state
- [ rsl_initLanIgmpSnoopObj ] 181: We need vlan if we want igmp snooping
- ath0 no private ioctls.
- ath1 no private ioctls.
- device eth0 left promiscuous mode
- br0: port 1(eth0) entering disabled state
- device eth0.2 entered promiscuous mode
- device eth0 entered promiscuous mode
- br0: port 1(eth0.2) entering forwarding state
- device eth0.3 entered promiscuous mode
- br0: port 2(eth0.3) entering forwarding state
- device eth0.4 entered promiscuous mode
- br0: port 3(eth0.4) entering forwarding state
- device eth0.5 entered promiscuous mode
- br0: port 4(eth0.5) entering forwarding state
- *********cal_data*******
- 020500023537707500000000*********end*******
- .....pid 228: wait the running hotplug to end itself.......
- ath_hal: 0.9.17.1 (AR5212, AR5416, AR9380, RF5111, RF5112, RF2413, RF5413, RF2316, RF2317, REGOPS_FUNC, WRITE_EEPROM, 11D)
- ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
- ath_dfs: Version 2.0.0
- Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
- ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
- ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
- PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
- __ath_attach: Set global_scn[0]
- ACBKMinfree = 48
- ACBEMinfree = 32
- ACVIMinfree = 16
- ACVOMinfree = 0
- CABMinfree = 48
- UAPSDMinfree = 0
- Restoring Cal data from Flash
- dfs_attach: use DFS enhancements
- DFS min filter rssiThresh = 18
- DFS max pulse dur = 151 ticks
- ath_get_caps[5105] rx chainmask mismatch actual 7 sc_chainmak 0
- ath_get_caps[5080] tx chainmask mismatch actual 7 sc_chainmak 0
- .....pid 228: wait the running hotplug to end itself.......
- Register wlan WPS function, dev=0x828a8000
- Register wlan button on function
- Register wlan button off function
- wifi0: Atheros ???: mem=0x1c000000, irq=136 hw_base=0xbc000000
- ath_netdev_set_macaddr: ffffffe8:ffffff94:fffffff6:0f:4d:50
- wlan_vap_create : enter. devhandle=0x828a82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
- wlan_vap_create : exit. devhandle=0x828a82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
- VAP device ath0 created
- ath0
- ath_netdev_set_macaddr: ffffffe8:ffffff94:fffffff6:0f:4d:50
- WARNING: Fragmentation with HT mode NOT ALLOWED!!
- Error for wireless request "Set Fragmentation Threshold" (8B24) :
- SET failed on device ath0 ; Invalid argument.
- wlan_setAllCfgFile bridgeName br0
- Reading topology file /var/Wireless/topology.conf ...
- 014.636: Reading radio configuration file /var/Wireless/80211g.ap_radio ...
- 014.637: Reading bss configuration file /var/Wireless/ath0.ap_bss ...
- ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
- 014.669: upnp_wps_device_init called
- l2_packet_receive - recvfrom: Network is down
- ni aponly is null!
- ni aponly is null!
- .....pid 228: wait the running hotplug to end itself.......
- ni aponly is null!
- ni aponly is null!
- .....pid 228: wait the running hotplug to end itself.......
- ni aponly is null!
- .....pid 228: wait the running hotplug to end itself.......
- l2_packet_receive - recvfrom: Network is down
- Before hook ppa
- PPA REG DONE, if_id=3, dev_if_index = 15
- ath1 no private ioctls.
- device ath0 entered promiscuous mode
- br0: port 5(ath0) entering forwarding state
- Reading topology file /var/Wireless/topology.conf .. ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
- .
- 020.419: Readibr0: port 5(ath0) entering disabled state
- ng radio configuration file /var/Wireless/80211g.ap_radio ...
- 020.420: Reading bss configuration file /var/Wireless/ath0.ap_bss ...
- br0: port 5(ath0) entering forwarding state
- 020.456: upnp_wps_device_init called
- l2_packet_receive - recvfrom: Network is down
- .....pid 228: wait the running hotplug to end itself.......
- .....pid 228: wait the running hotplug to end itself.......
- .....pid 228: wait the running hotplug to end itself.......
- br0: port 5(ath0) entering disabled state
- l2_packet_receive - recvfrom: Network is down
- br0: port 5(ath0) entering forwarding state
- sendto: No such file or directory
- send 2030 error 244, -1
- sendto: No such file or directory
- send 2004 error 244, -1
- .....pid 228: wait the running hotplug to end itself.......
- [ apiSetAdslTypeAndAnnexType ] 1369: /firmware/dsl_cpe_pipe.sh g997xtusecs 05 00 04 00 04 01 00 00
- nReturn=0
- nReturn=0
- nReturn=0 nDirection=0
- nReturn=0 nDirection=1
- nReturn=4 nDirection=0
- nReturn=0 nDirection=1
- nReturn=0
- iptables: Bad rule (does a matching rule exist in that chain?)
- radvd starting
- [ oal_dsl_createMainAtmIf ] 2209: br2684ctl -b -p 1 -c 0 -e 0 -q ubr,aal5:max_pcr=0,min_pcr=0 -a 0.8.35
- ........pid 226: pPlugDevId[0]=, plugDevClass[0]=, plugAction[0]=.........
- ........pid 228: pPlugDevId[0]=, plugDevClass[0]=, plugAction[0]=.........
- [ oal_dsl_createMainAtmIf ] 2253: ifconfig nas0 hw ether 68:94:F6:0F:4D:51
- Interface "nas0" created sucessfully
- [ oal_dsl_addAtmIf ] 2038: br2684ctl -b -p 1 -x 1 -c 0 -e 0 -q ubr,aal5:max_pcr=0,min_pcr=0 -a 0.8.35
- optarg : ubr,aal5:max_pcr=0,min_pcr=0Interface "nas0_1" created sucessfully
- device nas0_1 entered promiscuous mode
- br0: port 6(nas0_1) entering forwarding state
- iptables: Bad rule (does a matching rule exist in that chain?)
- iptables: Bad rule (does a matching rule exist in that chain?)
- [ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
- [ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
- ifx_ppa_init - init succeeded
- iptables: Bad rule (does a matching rule exist in that chain?)
- ifx_ppa_init - init succeeded
- iptables: Bad rule (does a matching rule exist in that chain?)
- ifx_ppa_init - init succeeded
- iptables: Bad rule (does a matching rule exist in that chain?)
- ip6tables: Bad rule (does a matching rule exist in that chain?)
- [ rsl_setStorageServiceObj ] 1140: mountFlag is 3,We start usb server
- killall: ushare: no process killed
- uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server.
- Benjamin Zores (C) 2005-2007, for GeeXboX Team.
- See http://ushare.geexbox.org/ for updates.
- iptables: Bad rule (does a matching rule exist in that chain?)
- iptables: Bad rule (does a matching rule exist in that chain?)
- GPL NetUSB up!
- kc 86 : run_telnetDBGDServer start
- kc 223 : init_DebugD end
- INFO176C: NetUSB 1.02.06, 00020620 : Jun 13 2012 16:37:47
- INFO176E: AUTH ISOC
- INFO176F: filterAudio
- usbcore: registered new interface driver KC NetUSB General Driver
- INFO0076: init proc : PAGE_SIZE 4096
- INFO17C8: Check mac address
- INFO1640: infomap c1381994
- INFO1643: sleep to wait br0 to wake up
- INFO02D0: use dev Name br0
- INFO164C: sleep to wait br0 end.
- INFO1665: UDP_BROAD 7437 tcpPort:625868800
- INFO02D0: use dev Name br0
- INFO154C: tcpConnector() started...
- Enable forwarding
- INFO1429: Bind to br0
- starting pid 245, tty '': '/sbin/getty -L ttyS0 115200 vt100'
- TD-W8970 login: admin
- Password:
- Jan 1 00:00:54 login[245]: root login on 'console'
- # cat /proc/cpuinfo
- system type : VR9
- processor : 0
- cpu model : MIPS 34Kc V5.6
- BogoMIPS : 332.59
- wait instruction : yes
- microsecond timers : yes
- tlb_entries : 16
- extra interrupt vector : yes
- hardware watchpoint : yes, count: 4, address/irw mask: [0x0ff8, 0x0ffc, 0x0ffb, 0x0ff8]
- ASEs implemented : mips16 dsp mt
- shadow register sets : 1
- core : 0
- VCED exceptions : not available
- VCEI exceptions : not available
- ~ # free -m
- total used free shared buffers
- Mem: 60888 41304 19584 0 4120
- -/+ buffers: 37184 23704
- Swap: 0 0 0
- ~ #
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement