Advertisement
teknoraver

kirkwood

Nov 19th, 2014
337
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 17.05 KB | None | 0 0
  1. __ __ _ _
  2. | \/ | __ _ _ ____ _____| | |
  3. | |\/| |/ _` | '__\ \ / / _ \ | |
  4. | | | | (_| | | \ V / __/ | |
  5. |_| |_|\__,_|_| \_/ \___|_|_|
  6. _ _ ____ _
  7. | | | | | __ ) ___ ___ | |_
  8. | | | |___| _ \ / _ \ / _ \| __|
  9. | |_| |___| |_) | (_) | (_) | |_
  10. \___/ |____/ \___/ \___/ \__|
  11. ** MARVELL BOARD: RD-88F6281A LE
  12.  
  13. U-Boot 1.1.4 (Jan 21 2009 - 15:55:04) Marvell version: 3.4.14
  14.  
  15. U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60
  16.  
  17. Soc: 88F6281 A0 (DDR2)
  18. CPU running @ 1200Mhz L2 running @ 400Mhz
  19. SysClock = 400Mhz , TClock = 200Mhz
  20.  
  21. DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
  22. DRAM CS[0] base 0x00000000 size 256MB
  23. DRAM CS[1] base 0x10000000 size 256MB
  24. DRAM Total size 512MB 16bit width
  25. Flash: 0 kB
  26. Addresses 8M - 0M are saved for the U-Boot usage.
  27. Mem malloc Initialization (8M - 7M): Done
  28. NAND:128 MB
  29.  
  30. CPU : Marvell Feroceon (Rev 1)
  31.  
  32. Streaming disabled
  33. Write allocate disabled
  34.  
  35. Module 0 is RGMII
  36. Module 1 is TDM
  37.  
  38. USB 0: host mode
  39. PEX 0: interface detected no Link.
  40. Net: egiga0, egiga1 [PRIME]
  41. Hit any key to stop autoboot: 0
  42.  
  43. NAND read: device 0 offset 0x100000, size 0x200000
  44. 2097152 bytes read: OK
  45. ## Booting image at 02000000 ...
  46. Image Name: Linux-2.6.22.18
  47. Created: 2009-02-01 17:00:18 UTC
  48. Image Type: ARM Linux Kernel Image (uncompressed)
  49. Data Size: 1934664 Bytes = 1.8 MB
  50. Load Address: 00008000
  51. Entry Point: 00008000
  52. Verifying Checksum ... OK
  53. OK
  54.  
  55. Starting kernel ...
  56.  
  57. Uncompressing Linux........................................................................................................................... done, booting the kernel.
  58. Linux version 2.6.22.18 (root@gandalf602) (gcc version 4.2.1 (CodeSourcery Sourcery G++ Lite 2007q3-51)) #1 Sun Feb 1 19:00:14 IST 2009
  59. CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
  60. Machine: Feroceon-KW
  61. Using UBoot passing parameters structure
  62. Memory policy: ECC disabled, Data cache writeback
  63. CPU0: D VIVT write-back cache
  64. CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
  65. CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
  66. Built 1 zonelists. Total pages: 130048
  67. Kernel command line: console=ttyS0,115200 rootfstype=squashfs root=/dev/mtdblock2 mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mv_phone_config=dev0:fxs,dev1:fxs
  68. PID hash table entries: 2048 (order: 11, 8192 bytes)
  69. Console: colour dummy device 80x30
  70. Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  71. Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  72. Memory: 256MB 256MB 0MB 0MB = 512MB total
  73. Memory: 515712KB available (3548K code, 252K data, 132K init)
  74. Mount-cache hash table entries: 512
  75. CPU: Testing write buffer coherency: ok
  76. NET: Registered protocol family 16
  77.  
  78. CPU Interface
  79. -------------
  80. SDRAM_CS0 ....base 00000000, size 256MB
  81. SDRAM_CS1 ....base 10000000, size 256MB
  82. SDRAM_CS2 ....disable
  83. SDRAM_CS3 ....disable
  84. PEX0_MEM ....base e8000000, size 128MB
  85. PEX0_IO ....base f2000000, size 1MB
  86. INTER_REGS ....base f1000000, size 1MB
  87. NFLASH_CS ....base fa000000, size 2MB
  88. SPI_CS ....base f4000000, size 16MB
  89. BOOT_ROM_CS ....no such
  90. DEV_BOOTCS ....no such
  91. CRYPT_ENG ....base f0000000, size 2MB
  92.  
  93. Marvell Development Board (LSP Version rdke_1.4.2.0_LSP_4.2.7)-- RD-88F6281A Soc: 88F6281 A0 LE
  94.  
  95. Detected Tclk 200000000 and SysClk 400000000
  96. MV Buttons Device Load
  97. Marvell USB EHCI Host controller #0: c0873600
  98. PEX0 interface detected no Link.
  99. PCI: bus0: Fast back to back transfers enabled
  100. SCSI subsystem initialized
  101. usbcore: registered new interface driver usbfs
  102. usbcore: registered new interface driver hub
  103. usbcore: registered new device driver usb
  104. NET: Registered protocol family 2
  105. Time: kw_clocksource clocksource has been installed.
  106. IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
  107. TCP established hash table entries: 65536 (order: 7, 524288 bytes)
  108. TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
  109. TCP: Hash tables configured (established 65536 bind 65536)
  110. TCP reno registered
  111. RTC registered
  112. Use the XOR engines (acceleration) for enhancing the following functions:
  113. o RAID 5 Xor calculation
  114. o kernel memcpy
  115. o kenrel memzero
  116. Number of XOR engines to use: 4
  117. cesadev_init(c00116e0)
  118. mvCesaInit: sessions=640, queue=64, pSram=f0000000
  119. MV Buttons Driver Load
  120. squashfs: version 3.3 (2007/10/31) Phillip Lougher
  121. squashfs: LZMA suppport for slax.org by jro
  122. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  123. io scheduler noop registered
  124. io scheduler anticipatory registered (default)
  125. Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
  126. serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
  127. serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
  128. RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
  129. loop: module loaded
  130. Loading Marvell Ethernet Driver:
  131. o Cached descriptors in DRAM
  132. o DRAM SW cache-coherency
  133. o Multi RX Queue support - 4 RX queues
  134. o Multi TX Queue support - 2 TX Queues
  135. o TCP segmentation offload enabled
  136. o Receive checksum offload enabled
  137. o Transmit checksum offload enabled
  138. o Network Fast Processing (Routing) supported
  139. o Network Fast Processing (NAT) supported
  140. o Proc tool API enabled
  141. o Gateway support enabled
  142. o Using Marvell Header Mode
  143. o L2 IGMP support
  144. o Rx descripors: q0=196 q1=196 q2=196 q3=196
  145. o Tx descripors: q0=256 q1=256
  146. o Loading network interface(s):
  147. o eth0, ifindex = 1, GbE port = 1
  148. o Loading Gateway interface(s):
  149. o Using command line network interface configuration
  150. o MTU set to 1500.
  151. o mac_addr 00:11:88:0f:62:81, VID 0x100, port list: port-0 port-1 port-2 port-3
  152. o eth1, ifindex = 2, GbE port = 0
  153. Port 3: Link-up, Full-duplex, Speed-100Mbps.
  154.  
  155. mvFpRuleDb (df450000): 16384 entries, 65536 bytes
  156. PPP generic driver version 2.4.2
  157. NET: Registered protocol family 24
  158. NFP (pppoe) init 32 entries, 4096 bytes
  159. Integrated Sata device found
  160. scsi0 : Marvell SCSI to SATA adapter
  161. scsi1 : Marvell SCSI to SATA adapter
  162. scsi 0:0:0:0: Direct-Access Hitachi HDS721616PLA380 P22O PQ: 0 ANSI: 5
  163. mrvlSCSI: Index <0>, SCSI Target, <0,0,0,0>
  164. mrvlSCSI: Disk will be pinned to <sda>
  165. sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
  166. sd 0:0:0:0: [sda] Write Protect is off
  167. sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
  168. sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
  169. sd 0:0:0:0: [sda] Write Protect is off
  170. sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
  171. sda: sda1 sda2 sda3
  172. sd 0:0:0:0: [sda] Attached SCSI disk
  173. sd 0:0:0:0: Attached scsi generic sg0 type 0
  174. NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
  175. NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)
  176. Scanning device for bad blocks
  177. Bad eraseblock 419 at 0x03460000
  178. 5 cmdlinepart partitions found on MTD device nand_mtd
  179. Using built in partition definition
  180. Creating 5 MTD partitions on "nand_mtd":
  181. 0x00000000-0x00100000 : "uboot"
  182. 0x00100000-0x00380000 : "uimage"
  183. 0x00380000-0x02000000 : "rootfs"
  184. 0x02000000-0x02180000 : "varfs"
  185. 0x00100000-0x02180000 : "flash"
  186. ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
  187. ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
  188. ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
  189. ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
  190. usb usb1: configuration #1 chosen from 1 choice
  191. hub 1-0:1.0: USB hub found
  192. hub 1-0:1.0: 1 port detected
  193. Initializing USB Mass Storage driver...
  194. usbcore: registered new interface driver usb-storage
  195. USB Mass Storage support registered.
  196. mice: PS/2 mouse device common for all mice
  197. i2c /dev entries driver
  198. Linux telephony interface: v1.00
  199. Marvell Telephony Driver:
  200. assembly=1,irq=0
  201. Setting Daisy Chain Mode
  202. TDM dual channel device rev 0x201
  203. Initializing channel 0
  204. Unit Type: FXS
  205. Proslic Si3215 Detected.
  206. Si321x Version = 3
  207. chip Type t=0
  208. Powerup the Slic
  209. Start Calibration(vBat = c5)
  210. Caliberation done
  211. Register 98 = 11
  212. Register 99 = 10
  213. Slic is Active
  214. FXS type : SI3215
  215. Slic-0: using linear mode
  216. FXS-0: RX sample 0, TX sample 0
  217. phone0 registered
  218. Initializing channel 1
  219. Unit Type: FXS
  220. Proslic Si3215 Detected.
  221. Si321x Version = 3
  222. chip Type t=0
  223. Powerup the Slic
  224. Start Calibration(vBat = c8)
  225. Caliberation done
  226. Register 98 = f
  227. Register 99 = d
  228. Slic is Active
  229. FXS type : SI3215
  230. Slic-1: using linear mode
  231. FXS-1: RX sample 10, TX sample 10
  232. phone1 registered
  233. md: linear personality registered for level -1
  234. md: raid1 personality registered for level 1
  235. raid6: int32x1 98 MB/s
  236. raid6: int32x2 114 MB/s
  237. raid6: int32x4 122 MB/s
  238. raid6: int32x8 110 MB/s
  239. raid6: using algorithm int32x4 (122 MB/s)
  240. md: raid6 personality registered for level 6
  241. md: raid5 personality registered for level 5
  242. md: raid4 personality registered for level 4
  243. raid5: measuring checksumming speed
  244. arm4regs : 1084.400 MB/sec
  245. 8regs : 755.200 MB/sec
  246. 32regs : 900.000 MB/sec
  247. raid5: using function: arm4regs (1084.400 MB/sec)
  248. sdhci: Secure Digital Host Controller Interface driver
  249. sdhci: Copyright(c) Pierre Ossman
  250. mvsdmmc: irq =28 start f1090000
  251. mvsdmmc: irq_detect=92
  252. Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
  253. ALSA device list:
  254. #0: Marvell mv88fx_snd ALSA driver
  255. nf_conntrack version 0.5.0 (4096 buckets, 32768 max)
  256. mvFpNatDb (df5ac000): 4096 entries, 16384 bytes
  257. ip_tables: (C) 2000-2006 Netfilter Core Team
  258. TCP cubic registered
  259. NET: Registered protocol family 1
  260. NET: Registered protocol family 17
  261. md: Autodetecting RAID arrays.
  262. md: autorun ...
  263. md: ... autorun DONE.
  264. VFS: Mounted root (squashfs filesystem) readonly.
  265. Freeing init memory: 132K
  266. [RCS]:Initiating boot sequence
  267. [RCS]:Setting global environment params
  268. [RCS]:Mounting PROC
  269. [RCS]:Discovering System and Platform type
  270. [RCS]: System:[RD-88F6281A]
  271. [RCS]: Platform:[rdke]
  272. [RCS]:Entering RootFS
  273. [RCS]:Discovering RootFS mount type
  274. [RCS]: Using ReadOnly rootfs
  275. [RCS]:Cleaning up and mounting sys folder
  276. [RCS]:Mounting proc/bus/usb folder
  277. [RCS]:Cleaning Mountpoint, Creating device and Mounting TmpFS
  278. [RCS]:Loading modules for current platform:
  279. [RCS]: Loading module [fat]
  280. [RCS]: Loading module [vfat]
  281. [RCS]: Loading module [msdos]
  282. [RCS]: Loading module [ntfs]
  283. NTFS driver 2.1.28 [Flags: R/O MODULE].
  284. [RCS]: Loading module [reiserfs]
  285. [RCS]: Loading module [xfs]
  286. SGI XFS with large block numbers, no debug enabled
  287. [RCS]: Loading module [smbfs]
  288. [RCS]: Loading Finished
  289. [RCS]:Cleaning Mountpoint, Un-Protecting and Mounting VarFS
  290. [RCS]: VarFS partition not specified. Using /dev/mtdblock3
  291. [RCS]: MTD Mode enabled
  292. [RCS]: Unlocking VarFS device [/dev/mtd3]
  293. Could not unlock MTD device: /dev/mtd3
  294. [RCS]: Mounting VarFS partition [/dev/mtdblock3]/[/dev/mtd3]
  295. jffs2_scan_inode_node(): CRC failed on node at 0x000267e0: Read 0xffffffff, calculated 0x6cb80475
  296. [RCS]: Mounting VarFS device [/dev/mtdblock3] succeded.
  297. [RCS]:Forwarding misc files/folders to TmpFS
  298. [RCS]:Setting misc files/folders in var
  299. [RCS]: /var/etc
  300. [RCS]: /etc/system
  301. [RCS]: /var/run, /var/lock, /var/cache, /var/db, /var/lib/php5
  302. ln: /var/cache: File exists
  303. ln: /var/pluto: File exists
  304. ln: /var/db: File exists
  305. [RCS]: /mnt
  306. [RCS]: /var/log
  307. [RCS]: /var/spool
  308. [RCS]:Setting various system parameters
  309. [RCS]: Raid Build Speed
  310. [RCS]:Switching to PHP bootstrap
  311. * Device XML config DB... [ OK ]
  312. * Initializing Timezone... [ OK ]
  313. * Starting syslogd... [ SKIP ]
  314. * Validate Default Hostname... [ OK ]
  315. * Generating Hosts File... [ OK ]
  316. * Configuring System Hostname... [ OK ]
  317. * Configuring System Users... [ OK ]
  318. * Set Fan Status (off)... [ OK ]
  319. * Starting udevd... [ OK ]
  320. * Configuring Loopback interface... [ OK ]
  321. * Configuring DNS... [ OK ]
  322. * Configuring WAN interface (DHCP)... eth0: started
  323. [ OK ]
  324. * Configuring WAN interface Firewall... [ OK ]
  325. * Configuring WAN interface NAT... [ OK ]
  326. * Starting Initialization WLAN interfaces... ap8x: module license 'Proprietary' taints kernel.
  327. * Initialization WLAN interfaces... [ OK ]
  328. * Starting configuring WLAN interface (AP)... wlan interface not present[ FAIL ]
  329. * Starting Configuring LAN ... mv_gateway: starting eth1
  330. * Configuring LAN interface... [ OK ]
  331. * Configuring DNS Forwarder... (DNSMASQ) [ OK ]
  332. Network Fast Processing Enabled
  333. * Configuring NFP... [ OK ]
  334. * Configuring IPSEC... [ OK ]
  335. * Configuring WAN interface Forwarding... [ OK ]
  336. * Configuring Samba... [ OK ]
  337. * Updating Disk configuration...
  338. - Updating disk /dev/sda:
  339. [ OK ]
  340. * Finishing updating disk configuration... [ OK ]
  341. * Starting assemble of volumes arrays...
  342. - Assembling volume Non-Mirrored:
  343. [ Skip ]
  344. * Finishing assemble of volumes arrays... [ OK ]
  345. * Configuring Disks Read Ahead... [ OK ]
  346. * Configuring Disks Timeout... [ OK ]
  347. * Starting mount of volumes...
  348. - Mounting volume Non-Mirrored:
  349. kjournald starting. Commit interval 5 seconds
  350. EXT3-fs warning: checktime reached, running e2fsck is recommended
  351. EXT3 FS on sda3, internal journal
  352. EXT3-fs: recovery complete.
  353. EXT3-fs: mounted filesystem with writeback data mode.
  354. [ OK ]
  355. * Finishing mount of volumes... [ OK ]
  356. * Starting WebGUI... [ OK ]
  357. * Checking System Language... [ OK ]
  358. usbcore: registered new interface driver usblp
  359. drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
  360. * Starting cups... [ OK ]
  361. * Configuring Samba... [ OK ]
  362. * Starting Samba Daemons... [ OK ]
  363. * Starting dropbear... [ OK ]
  364. * Starting iTunes Daemon... [ SKIP ]
  365. * Starting PV Media Server... [ SKIP ]
  366. * Starting buttons daemon... [ OK ]
  367. * Starting Marvell discovery...... [ OK ]
  368. *** Applying WLAN Settings fo AP...
  369. [ FAIL ]
  370. [ FAIL ]
  371. * Starting IGMP PROXY Daemon... [ OK ]
  372. [RCS]:Displaying banner
  373.  
  374.  
  375. *** Marvell Semiconductors ltd.
  376. This is MRVL-NAS version: [1.4.2.0] running on board: [RD-88F6281A]
  377. Built at: Sun Feb 1 19:24:17 IST 2009
  378.  
  379. WAN IP address: 169.254.203.48 (static - random)
  380.  
  381. Port configuration:
  382.  
  383. WAN -> eth0
  384.  
  385.  
  386. BusyBox v1.1.3 (2009.02.01-17:01+0000) Built-in shell (ash)
  387. Enter 'help' for a list of built-in commands.
  388.  
  389. # uname -a
  390. Linux Kirkwood.local 2.6.22.18 #1 Sun Feb 1 19:00:14 IST 2009 armv5tejl unknown
  391.  
  392. # cat /proc/cpuinfo
  393. Processor : ARM926EJ-S rev 1 (v5l)
  394. BogoMIPS : 1192.75
  395. Features : swp half thumb fastmult edsp
  396. CPU implementer : 0x56
  397. CPU architecture: 5TE
  398. CPU variant : 0x2
  399. CPU part : 0x131
  400. CPU revision : 1
  401. Cache type : write-back
  402. Cache clean : cp15 c7 ops
  403. Cache lockdown : format C
  404. Cache format : Harvard
  405. I size : 16384
  406. I assoc : 4
  407. I line length : 32
  408. I sets : 128
  409. D size : 16384
  410. D assoc : 4
  411. D line length : 32
  412. D sets : 128
  413.  
  414. Hardware : Feroceon-KW
  415. Revision : 0000
  416. Serial : 0000000000000000
  417.  
  418. # cat /proc/meminfo
  419. MemTotal: 515956 kB
  420. MemFree: 443352 kB
  421. Buffers: 8936 kB
  422. Cached: 24456 kB
  423. SwapCached: 0 kB
  424. Active: 24848 kB
  425. Inactive: 18624 kB
  426. SwapTotal: 257032 kB
  427. SwapFree: 257032 kB
  428. Dirty: 0 kB
  429. Writeback: 0 kB
  430. AnonPages: 10112 kB
  431. Mapped: 6240 kB
  432. Slab: 19520 kB
  433. SReclaimable: 1476 kB
  434. SUnreclaim: 18044 kB
  435. PageTables: 324 kB
  436. NFS_Unstable: 0 kB
  437. Bounce: 0 kB
  438. CommitLimit: 515008 kB
  439. Committed_AS: 31596 kB
  440. VmallocTotal: 122880 kB
  441. VmallocUsed: 4728 kB
  442. VmallocChunk: 118144 kB
  443.  
  444. # df -h
  445. Filesystem Size Used Available Use% Mounted on
  446. /dev/mtdblock2 16.0M 16.0M 0 100% /
  447. none 251.9M 248.0k 251.7M 0% /tmp
  448. /dev/mtdblock3 1.5M 452.0k 1.1M 29% /var
  449. udev 251.9M 4.0k 251.9M 0% /dev
  450. /dev/sda3 147.8G 187.6M 147.6G 0% /tmp/mnt/9511
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement