[09:46:25][I][logger:351]: Log initialized
[09:46:25][C][ota:473]: There have been 7 suspected unsuccessful boot attempts.
[09:46:25][D][esp32.preferences:114]: Saving 1 preferences to flash...
[09:46:25][D][esp32.preferences:143]: Saving 1 preferences to flash: 0 cached, 1 written, 0 failed
[09:46:25][I][app:029]: Running through setup()...
[09:46:25][I][i2c.arduino:183]: Performing I2C bus recovery
[09:46:25][C][ina228:061]: Setting up INA228...
[09:46:25][D][ina228:108]: Reset
[09:46:25][D][ina228:022]: read_u16_ 0x3E, ret= 0, raw 0x4954
[09:46:25][D][ina228:022]: read_u16_ 0x3F, ret= 0, raw 0x8122
[09:46:25][I][ina228:075]: Manufacturer: 0x5449, Device ID: 0x0228, Revision: 1
[09:46:25][D][ina228:022]: read_u16_ 0x01, ret= 0, raw 0xD4FF
[09:46:25][D][ina228:085]: Read REG_ADC_CONFIG returned OK, 0xFFD4
[09:46:25][D][ina228:093]: Write REG_ADC_CONFIG2 returned OK, 0xFB68
[09:46:25][D][ina228:022]: read_u16_ 0x01, ret= 0, raw 0x68FB
[09:46:25][D][ina228:097]: Checking ... Read REG_ADC_CONFIG returned OK, 0xFB68
[09:46:25][D][ina228:138]: New Rshunt=0.001110 ohm, max current=40.000
[09:46:25][D][ina228:139]: New CURRENT_LSB=0.000038, SHUNT_CAL=2216
[09:46:25][D][ina228:145]: Setting ADCRANGE = 1
[09:46:25][D][ina228:022]: read_u16_ 0x00, ret= 0, raw 0x0000
[09:46:25][D][ina228:148]: set_adc_ranged_ OK, read: 0x0000
[09:46:25][D][ina228:152]: set_adc_range_ OK, write: 0x0010
[09:46:25][D][sensor:094]: 'Uptime Sensor': Sending state 0.28800 s with 0 decimals of accuracy
[09:46:25][D][ina228:041]: read_s20_4_ 0x04, ret= 0, raw 0x00805900
[09:46:25][D][ina228:160]: read_volt_shunt_ OK, 0x00000598, adc_range=1
[09:46:25][D][sensor:094]: 'INA228 Shunt Voltage': Sending state 0.11187 mV with 5 decimals of accuracy
[09:46:25][D][ina228:041]: read_s20_4_ 0x05, ret= 0, raw 0x00B06D0C
[09:46:25][D][ina228:175]: read_voltage_ OK, 0x0000C6DB
[09:46:25][D][sensor:094]: 'INA228 Bus Voltage': Sending state 9.94277 V with 5 decimals of accuracy
[09:46:25][D][ina228:022]: read_u16_ 0x06, ret= 0, raw 0x030C
[09:46:25][D][ina228:188]: read_die_temp_ OK, 0x0C03
[09:46:25][D][sensor:094]: 'INA228 DIE Temperature': Sending state 24.02344 °C with 5 decimals of accuracy
[09:46:25][D][ina228:041]: read_s20_4_ 0x07, ret= 0, raw 0x0090A300
[09:46:25][D][ina228:197]: read_current_ is TRUE, 0x00000A39, current_lsb=0.000038
[09:46:26][D][sensor:094]: 'INA228 Current': Sending state 0.09983 A with 5 decimals of accuracy
[09:46:26][D][ina228:206]: read_power_1 ret= 0, 0x00271F00
[09:46:26][D][ina228:209]: read_power_2 ret= 0, 0x00001F27
[09:46:26][D][sensor:094]: 'INA228 Power': Sending state 0.97351 W with 5 decimals of accuracy
[09:46:26][D][ina228:022]: read_u16_ 0x0B, ret= 0, raw 0x0320
[09:46:26][D][ina228:257]: read_diagnostics_and_act_ OK, 0x2003
[09:46:26][D][ina228:220]: read_energy_1 ret_err= 0, raw 0x8D03000000
[09:46:26][D][ina228:224]: read_energy_2 ret_err= 0, 0x38D, current_lsb=0.000038, overflow_cnt=0
[09:46:26][D][sensor:094]: 'INA228 Energy': Sending state 1.77539 J with 5 decimals of accuracy
[09:46:26][D][ina228:236]: read_charge_1 ret_err= 0, 0xA912000000
[09:46:26][D][ina228:248]: read_charge_2 ret_err=0, 0x12A9, current_lsb=0.000038, overflow_cnt=0
[09:46:26][D][sensor:094]: 'INA228 Charge': Sending state 0.18223 C with 5 decimals of accuracy
[09:46:26][W][component:214]: Component ina228.sensor took a long time for an operation (0.16 s).
[09:46:26][W][component:215]: Components should block for at most 20-30ms.
[09:46:26][D][ina228:041]: read_s20_4_ 0x04, ret= 0, raw 0x00805900
[09:46:26][D][ina228:160]: read_volt_shunt_ OK, 0x00000598, adc_range=1
[09:46:26][D][sensor:094]: 'INA228 Shunt Voltage': Sending state 0.11187 mV with 5 decimals of accuracy
[09:46:26][D][ina228:041]: read_s20_4_ 0x05, ret= 0, raw 0x00B06D0C
[09:46:26][D][ina228:175]: read_voltage_ OK, 0x0000C6DB
[09:46:26][D][sensor:094]: 'INA228 Bus Voltage': Sending state 9.94277 V with 5 decimals of accuracy
[09:46:26][D][ina228:022]: read_u16_ 0x06, ret= 0, raw 0x080C
[09:46:26][D][ina228:188]: read_die_temp_ OK, 0x0C08
[09:46:26][D][sensor:094]: 'INA228 DIE Temperature': Sending state 24.06250 °C with 5 decimals of accuracy
[09:46:26][D][ina228:041]: read_s20_4_ 0x07, ret= 0, raw 0x0030A200
[09:46:26][D][ina228:197]: read_current_ is TRUE, 0x00000A23, current_lsb=0.000038
[09:46:26][D][sensor:094]: 'INA228 Current': Sending state 0.09899 A with 5 decimals of accuracy
[09:46:26][D][ina228:206]: read_power_1 ret= 0, 0x00AC1F00
[09:46:26][D][ina228:209]: read_power_2 ret= 0, 0x00001FAC
[09:46:26][D][sensor:094]: 'INA228 Power': Sending state 0.98975 W with 5 decimals of accuracy
[09:46:26][D][ina228:022]: read_u16_ 0x0B, ret= 0, raw 0x0320
[09:46:26][D][ina228:257]: read_diagnostics_and_act_ OK, 0x2003
[09:46:26][D][ina228:220]: read_energy_1 ret_err= 0, raw 0x3D05000000
[09:46:26][D][ina228:224]: read_energy_2 ret_err= 0, 0x53D, current_lsb=0.000038, overflow_cnt=0
[09:46:26][D][sensor:094]: 'INA228 Energy': Sending state 2.61914 J with 5 decimals of accuracy
[09:46:26][D][ina228:236]: read_charge_1 ret_err= 0, 0x9B1B000000
[09:46:26][D][ina228:248]: read_charge_2 ret_err=0, 0x1B9B, current_lsb=0.000038, overflow_cnt=0
[09:46:26][D][sensor:094]: 'INA228 Charge': Sending state 0.26958 C with 5 decimals of accuracy
[09:46:26][W][component:214]: Component ina228.sensor took a long time for an operation (0.15 s).
[09:46:26][W][component:215]: Components should block for at most 20-30ms.
[09:46:28][D][ina228:041]: read_s20_4_ 0x04, ret= 0, raw 0x00005B00
[09:46:28][D][ina228:160]: read_volt_shunt_ OK, 0x000005B0, adc_range=1
[09:46:28][D][sensor:094]: 'INA228 Shunt Voltage': Sending state 0.11375 mV with 5 decimals of accuracy
[09:46:28][D][ina228:041]: read_s20_4_ 0x05, ret= 0, raw 0x00706E0C
[09:46:28][D][ina228:175]: read_voltage_ OK, 0x0000C6E7
[09:46:28][D][sensor:094]: 'INA228 Bus Voltage': Sending state 9.94512 V with 5 decimals of accuracy
[09:46:28][D][ina228:022]: read_u16_ 0x06, ret= 0, raw 0x020C
[09:46:28][D][ina228:188]: read_die_temp_ OK, 0x0C02
[09:46:28][D][sensor:094]: 'INA228 DIE Temperature': Sending state 24.01562 °C with 5 decimals of accuracy
[09:46:28][D][ina228:041]: read_s20_4_ 0x07, ret= 0, raw 0x00D0A600
[09:46:28][D][ina228:197]: read_current_ is TRUE, 0x00000A6D, current_lsb=0.000038
[09:46:28][D][sensor:094]: 'INA228 Current': Sending state 0.10181 A with 5 decimals of accuracy
[09:46:28][D][ina228:206]: read_power_1 ret= 0, 0x001D2100
[09:46:28][D][ina228:209]: read_power_2 ret= 0, 0x0000211D
[09:46:28][D][sensor:094]: 'INA228 Power': Sending state 1.03479 W with 5 decimals of accuracy
[09:46:28][D][ina228:022]: read_u16_ 0x0B, ret= 0, raw 0x0320
[09:46:28][D][ina228:257]: read_diagnostics_and_act_ OK, 0x2003
[09:46:28][D][ina228:220]: read_energy_1 ret_err= 0, raw 0x3A09000000
[09:46:28][D][ina228:224]: read_energy_2 ret_err= 0, 0x93A, current_lsb=0.000038, overflow_cnt=0
[09:46:28][D][sensor:094]: 'INA228 Energy': Sending state 4.61328 J with 5 decimals of accuracy
[09:46:28][D][ina228:236]: read_charge_1 ret_err= 0, 0x2D30000000
[09:46:28][D][ina228:248]: read_charge_2 ret_err=0, 0x302D, current_lsb=0.000038, overflow_cnt=0
[09:46:28][D][sensor:094]: 'INA228 Charge': Sending state 0.47047 C with 5 decimals of accuracy
[09:46:28][W][component:214]: Component ina228.sensor took a long time for an operation (0.15 s).
[09:46:28][W][component:215]: Components should block for at most 20-30ms.
[09:46:30][D][ina228:041]: read_s20_4_ 0x04, ret= 0, raw 0x00005D00
[09:46:30][D][ina228:160]: read_volt_shunt_ OK, 0x000005D0, adc_range=1
[09:46:30][D][sensor:094]: 'INA228 Shunt Voltage': Sending state 0.11625 mV with 5 decimals of accuracy
[09:46:30][D][ina228:041]: read_s20_4_ 0x05, ret= 0, raw 0x00E06D0C
[09:46:30][D][ina228:175]: read_voltage_ OK, 0x0000C6DE
[09:46:30][D][sensor:094]: 'INA228 Bus Voltage': Sending state 9.94336 V with 5 decimals of accuracy
[09:46:30][D][ina228:022]: read_u16_ 0x06, ret= 0, raw 0x020C
[09:46:30][D][ina228:188]: read_die_temp_ OK, 0x0C02
[09:46:30][D][sensor:094]: 'INA228 DIE Temperature': Sending state 24.01562 °C with 5 decimals of accuracy
[09:46:30][D][ina228:041]: read_s20_4_ 0x07, ret= 0, raw 0x0030A800
[09:46:30][D][ina228:197]: read_current_ is TRUE, 0x00000A83, current_lsb=0.000038
[09:46:30][D][sensor:094]: 'INA228 Current': Sending state 0.10265 A with 5 decimals of accuracy
[09:46:30][D][ina228:206]: read_power_1 ret= 0, 0x001D2000
[09:46:30][D][ina228:209]: read_power_2 ret= 0, 0x0000201D
[09:46:30][D][sensor:094]: 'INA228 Power': Sending state 1.00354 W with 5 decimals of accuracy
[09:46:30][D][ina228:022]: read_u16_ 0x0B, ret= 0, raw 0x0320
[09:46:30][D][ina228:257]: read_diagnostics_and_act_ OK, 0x2003
[09:46:30][D][ina228:220]: read_energy_1 ret_err= 0, raw 0x340D000000
[09:46:30][D][ina228:224]: read_energy_2 ret_err= 0, 0xD34, current_lsb=0.000038, overflow_cnt=0
[09:46:30][D][sensor:094]: 'INA228 Energy': Sending state 6.60156 J with 5 decimals of accuracy
[09:46:30][D][ina228:236]: read_charge_1 ret_err= 0, 0xB244000000
[09:46:30][D][ina228:248]: read_charge_2 ret_err=0, 0x44B2, current_lsb=0.000038, overflow_cnt=0
[09:46:30][D][sensor:094]: 'INA228 Charge': Sending state 0.67085 C with 5 decimals of accuracy
[09:46:30][W][component:214]: Component ina228.sensor took a long time for an operation (0.15 s).
[09:46:30][W][component:215]: Components should block for at most 20-30ms.
[09:46:32][D][ina228:041]: read_s20_4_ 0x04, ret= 0, raw 0x00405900
[09:46:32][D][ina228:160]: read_volt_shunt_ OK, 0x00000594, adc_range=1
[09:46:32][D][sensor:094]: 'INA228 Shunt Voltage': Sending state 0.11156 mV with 5 decimals of accuracy
[09:46:32][D][ina228:041]: read_s20_4_ 0x05, ret= 0, raw 0x00806D0C
[09:46:32][D][ina228:175]: read_voltage_ OK, 0x0000C6D8
[09:46:32][D][sensor:094]: 'INA228 Bus Voltage': Sending state 9.94219 V with 5 decimals of accuracy
[09:46:32][D][ina228:022]: read_u16_ 0x06, ret= 0, raw 0x080C
[09:46:32][D][ina228:188]: read_die_temp_ OK, 0x0C08
[09:46:32][D][sensor:094]: 'INA228 DIE Temperature': Sending state 24.06250 °C with 5 decimals of accuracy
[09:46:32][D][ina228:041]: read_s20_4_ 0x07, ret= 0, raw 0x0080A400
[09:46:32][D][ina228:197]: read_current_ is TRUE, 0x00000A48, current_lsb=0.000038
[09:46:32][D][sensor:094]: 'INA228 Current': Sending state 0.10040 A with 5 decimals of accuracy
[09:46:32][D][ina228:206]: read_power_1 ret= 0, 0x00902000
[09:46:32][D][ina228:209]: read_power_2 ret= 0, 0x00002090
[09:46:32][D][sensor:094]: 'INA228 Power': Sending state 1.01758 W with 5 decimals of accuracy
[09:46:32][D][ina228:022]: read_u16_ 0x0B, ret= 0, raw 0x0320
[09:46:32][D][ina228:257]: read_diagnostics_and_act_ OK, 0x2003
[09:46:32][D][ina228:220]: read_energy_1 ret_err= 0, raw 0x2F11000000
[09:46:32][D][ina228:224]: read_energy_2 ret_err= 0, 0x112F, current_lsb=0.000038, overflow_cnt=0
[09:46:32][D][sensor:094]: 'INA228 Energy': Sending state 8.59180 J with 5 decimals of accuracy
[09:46:32][D][ina228:236]: read_charge_1 ret_err= 0, 0x3D59000000
[09:46:32][D][ina228:248]: read_charge_2 ret_err=0, 0x593D, current_lsb=0.000038, overflow_cnt=0
[09:46:32][D][sensor:094]: 'INA228 Charge': Sending state 0.87147 C with 5 decimals of accuracy
[09:46:32][W][component:214]: Component ina228.sensor took a long time for an operation (0.15 s).
[09:46:32][W][component:215]: Components should block for at most 20-30ms.