API tools faq
paste
Advertisement
ScottHelme

EE BrightBox - dmesg

ScottHelme
Jan 13th, 2014
448
0
Never
Add comment
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
text 9.04 KB | None | 0 0
raw download clone embed print report
  1. root@BrightBox:/ramdisk/mnt/storage # dmesg
  2. Linux version 2.6.30 (brian_chang@buildbed) (gcc version 4.1.2) #1 Fri Sep 21 02:51:02 CST 2012
  3. Detected Broadcom 0x6328 CPU revision 10b0
  4. CPU frequency is 320 MHz
  5. 64MB of RAM installed
  6. registering 32 GPIOs
  7. console [early0] enabled
  8. CPU revision is: 0002a075 (Broadcom BCM63281)
  9. board_bcm9632x: board name: AR7516AAW
  10. Determined physical RAM map:
  11. memory: 03f00000 @ 00000000 (usable)
  12. Zone PFN ranges:
  13. DMA 0x00000000 -> 0x00001000
  14. Normal 0x00001000 -> 0x00003f00
  15. Movable zone start PFN for each node
  16. early_node_map[1] active PFN ranges
  17. 0: 0x00000000 -> 0x00003f00
  18. On node 0 totalpages: 16128
  19. free_area_init_node: node 0, pgdat 8024bb30, node_mem_map 81000000
  20. DMA zone: 32 pages used for memmap
  21. DMA zone: 0 pages reserved
  22. DMA zone: 4064 pages, LIFO batch:0
  23. Normal zone: 94 pages used for memmap
  24. Normal zone: 11938 pages, LIFO batch:1
  25. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
  26. Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro rootfstype=squashfs
  27. wait instruction: enabled
  28. Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
  29. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
  30. NR_IRQS:80
  31. PID hash table entries: 256 (order: 8, 1024 bytes)
  32. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
  33. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
  34. Memory: 61368k/64512k available (1912k kernel code, 3124k reserved, 436k data, 120k init, 0k highmem)
  35. Calibrating delay loop... 318.46 BogoMIPS (lpj=159232)
  36. Mount-cache hash table entries: 512
  37. --Kernel Config--
  38. SMP=0
  39. PREEMPT=0
  40. DEBUG_SPINLOCK=0
  41. DEBUG_MUTEXES=0
  42. net_namespace: 536 bytes
  43. /proc/net/netfilter/nf_cli_bw_mon created
  44. NET: Registered protocol family 16
  45. registering PCI controller with io_map_base unset
  46. bio: create slab <bio-0> at 0
  47. pci 0000:00:00.0: PME# supported from D0 D3hot
  48. pci 0000:00:00.0: PME# disabled
  49. pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
  50. pci 0000:01:00.0: supports D1 D2
  51. pci 0000:00:00.0: PCI bridge, secondary bus 0000:01
  52. pci 0000:00:00.0: IO window: disabled
  53. pci 0000:00:00.0: MEM window: 0x10f00000-0x10ffffff
  54. pci 0000:00:00.0: PREFETCH window: disabled
  55. PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
  56. PCI: Setting latency timer of device 0000:00:00.0 to 64
  57. BLOG v3.0 Initialized
  58. BLOG Rule v1.0 Initialized
  59. Broadcom IQoS v0.1 Sep 21 2012 02:49:54 initialized
  60. NET: Registered protocol family 8
  61. NET: Registered protocol family 20
  62. NET: Registered protocol family 2
  63. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  64. TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  65. TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
  66. TCP: Hash tables configured (established 2048 bind 2048)
  67. TCP reno registered
  68. NET: Registered protocol family 1
  69. Total # RxBds=848
  70. bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
  71.  
  72. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  73. msgmni has been set to 119
  74. io scheduler noop registered (default)
  75. PCI: Setting latency timer of device 0000:00:00.0 to 64
  76. aer 0000:00:00.0:pcie02: service driver aer loaded
  77. bcm632x-uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm632x-uart
  78. console handover: boot [early0] -> real [ttyS0]
  79. loop: module loaded
  80. PPP generic driver version 2.4.2
  81. NET: Registered protocol family 24
  82. PPPoL2TP kernel driver, V1.0
  83. m25p80 spi0.0: mx25l6405d (8192 Kbytes)
  84. Creating 6 MTD partitions on "spi0.0":
  85. 0x00000000e000-0x00000000f000 : "manuf"
  86. 0x00000000f000-0x000000010000 : "nvram"
  87. 0x000000110000-0x0000007f0000 : "rootfs"
  88. 0x000000010000-0x0000007f0000 : "priimg"
  89. 0x0000007f0000-0x000000800000 : "pricfg"
  90. 0x000000000000-0x00000000e000 : "bootldr"
  91. bcm632x-hsspi bcm632x-hsspi.0: at 0xb0001000 (irq 37, FIFOs size 510) v1.0
  92. Registered led device: dsl:sync
  93. Registered led device: dsl:data
  94. Registered led device: wps:green
  95. Registered led device: sys:a
  96. Registered led device: sys:b
  97. Registered led device: sys:c
  98. Registered led device: sys:d
  99. GACT probability on
  100. u32 classifier
  101. Actions configured
  102. TCP cubic registered
  103. NET: Registered protocol family 17
  104. Bridge firewalling registered
  105. Initializing MCPD Module
  106. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  107. All bugs added by David S. Miller <davem@redhat.com>
  108. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  109. Freeing unused kernel memory: 120k freed
  110. gpio-buttons driver version 0.1.2
  111. input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
  112. Button Hotplug driver version 0.4.1
  113. arc_oshal: module license 'Propritary' taints kernel.
  114. Disabling lock debugging due to kernel taint
  115.  
  116. oshal_init(1066) DRV: Created Successfully
  117.  
  118. ARC_KERNEL_OSIX_init(396) DRV: Created Successfully
  119. Broadcom Logger v0.1 Sep 21 2012 02:51:21
  120. Initialized fcache state
  121. Broadcom Packet Flow Cache Char Driver v2.2 Sep 21 2012 02:51:23 Registered<242>
  122. Created Proc FS /procfs/fcache
  123. Broadcom Packet Flow Cache registered with netdev chain
  124. Broadcom Packet Flow Cache learning via BLOG enabled.
  125. Constructed Broadcom Packet Flow Cache v2.2 Sep 21 2012 02:51:23
  126. Broadcom BCM6328B0 Ethernet Network Device v0.1 Sep 21 2012 02:51:25
  127. ETH Init: Ch:0 - 180 tx BDs at 0xa3946000
  128. ETH Init: Ch:0 - 400 rx BDs at 0xa3a20000
  129. bcm632x-dg: register bcmsw
  130. eth0: MAC Address: 88:03:55:19:7F:EB
  131. eth1: MAC Address: 88:03:55:19:7F:EB
  132. eth2: MAC Address: 88:03:55:19:7F:EB
  133. eth3: MAC Address: 88:03:55:19:7F:EB
  134. Broadcom 802.1Q VLAN Interface, v0.1
  135. bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.4 Sep 21 2012 02:51:33
  136. bcmxtmcfg: bcmxtmcfg_init entry
  137. adsl: adsl_init entry
  138. Broadcom Power Management v0.1 Sep 21 2012 02:52:42
  139. Broadcom WLAN configuration service start
  140. PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
  141. PCI: Setting latency timer of device 0000:01:00.0 to 64
  142. wl: passivemode=1
  143. wl: napimode=0
  144. wl: allocskbmode=1
  145. wl:force using embedded data
  146. wlc_bmac_attach(2582): BpGetWirelessFlags NIY!
  147. wl0: Broadcom BCMa8dc 802.11 Wireless Controller 5.100.96.0.cpe4.10L01a.8
  148. bcm632x-dg: register wl0
  149. ip_tables: (C) 2000-2006 Netfilter Core Team
  150. Netfilter messages via NETLINK v0.30.
  151. nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
  152. ctnetlink v0.93: registering with nfnetlink.
  153. xt_time: kernel timezone is -0000
  154. IMQ driver loaded successfully.
  155. Hooking IMQ after NAT on PREROUTING.
  156. Hooking IMQ before NAT on POSTROUTING.
  157. BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
  158. BcmAdsl_Initialize(202): BpGetRj11InnerOuterPairGpios NIY
  159. pSdramPHY=0xA3FFFFF8, 0xD18BD18B 0xD18BD18B
  160. *** PhySdramSize got adjusted: 0x82CDC => 0x98878 ***
  161. AdslCoreSharedMemInit: shareMemAvailable=423776
  162. AdslCoreHwReset: pLocSbSta=83120000 bkupThreshold=1600
  163. AdslCoreHwReset: AdslOemDataAddr = 0xA3F77D28
  164. BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
  165. BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
  166. BcmAdsl_Initialize=0xC0404EF8, g_pFnNotifyCallback=0xC04BA8D4
  167. XTM Init: Ch:0 - 400 rx BDs at 0xa3bc4000
  168. XTM Init: Ch:1 - 16 rx BDs at 0xa29af780
  169. device eth0 entered promiscuous mode
  170. device eth1 entered promiscuous mode
  171. device eth2 entered promiscuous mode
  172. device eth3 entered promiscuous mode
  173. br0: port 1(eth0) entering disabled state
  174. br0: port 2(eth1) entering disabled state
  175. br0: port 3(eth2) entering disabled state
  176. br0: port 4(eth3) entering disabled state
  177. eth1 Link UP 100 mbps full duplex
  178. br0: port 2(eth1) entering forwarding state
  179. device wl0 entered promiscuous mode
  180. br0: port 5(wl0) entering forwarding state
  181. device wl0.1 entered promiscuous mode
  182. device wl0.2 entered promiscuous mode
  183. usbcore: registered new interface driver usbfs
  184. usbcore: registered new interface driver hub
  185. usbcore: registered new device driver usb
  186. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  187. bcm632x-usb-ehci bcm632x-usb-ehci.0: Broadcom BCM632X series SoCs built-in EHCI controller
  188. bcm632x-usb-ehci bcm632x-usb-ehci.0: new USB bus registered, assigned bus number 1
  189. bcm632x-usb-ehci bcm632x-usb-ehci.0: irq 50, io mem 0xb0002500
  190. bcm632x-usb-ehci bcm632x-usb-ehci.0: USB 2.0 started, EHCI 1.00
  191. usb usb1: configuration #1 chosen from 1 choice
  192. hub 1-0:1.0: USB hub found
  193. hub 1-0:1.0: 1 port detected
  194. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  195. bcm632x-usb-ohci bcm632x-usb-ohci.0: Broadcom BCM632X series SoCs built-in OHCI controller
  196. bcm632x-usb-ohci bcm632x-usb-ohci.0: new USB bus registered, assigned bus number 2
  197. bcm632x-usb-ohci bcm632x-usb-ohci.0: irq 49, io mem 0xb0002600
  198. bcm632x-usb-ohci bcm632x-usb-ohci.0: init err (c8300000 0000)
  199. bcm632x-usb-ohci bcm632x-usb-ohci.0: startup error -79
  200. bcm632x-usb-ohci bcm632x-usb-ohci.0: USB bus 2 deregistered
  201. bcm632x-usb-ohci: probe of bcm632x-usb-ohci.0 failed with error -79
  202. usbcore: registered new interface driver usbserial
  203. USB Serial support registered for generic
  204. usbcore: registered new interface driver usbserial_generic
  205. usbserial: USB Serial Driver core
  206. fuse init (API version 7.11)
  207. SCSI subsystem initialized
  208. Driver 'sd' needs updating - please use bus_type methods
  209. Initializing USB Mass Storage driver...
  210. usbcore: registered new interface driver usb-storage
  211. USB Mass Storage support registered.
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
Public Pastes
Advertisement
We use cookies for various purposes including analytics. By continuing to use Pastebin, you agree to our use of cookies as described in the Cookies Policy.  OK, I Understand
Not a member of Pastebin yet?
Sign Up, it unlocks many cool features!