GPSTime rev_118

/********* Pleasedontcode.com **********

    Pleasedontcode thanks you for automatic code generation! Enjoy your code!

    - Terms and Conditions:
    You have a non-exclusive, revocable, worldwide, royalty-free license
    for personal and commercial use. Attribution is optional; modifications
    are allowed, but you're responsible for code maintenance. We're not
    liable for any loss or damage. For full terms,
    please visit pleasedontcode.com/termsandconditions.

    - Project: GPSTime
    - Source Code compiled for: Arduino Uno
    - Source Code created on: 2023-11-25 00:08:38
    - Source Code generated by: Francesco Alessandro

********* Pleasedontcode.com **********/
/****** DEFINITION OF LIBRARIES *****/
#include <Arduino.h>
#include <SoftwareSerial.h>
#include <Wire.h>
#include <MicroNMEA.h>
#include <LiquidCrystal_I2C.h>

/****** SYSTEM REQUIREMENT 1 *****/
/* Reads hour, minutes and seconds from GPS */
/* module using MicroNMEA library. Display hours, */
/* minutes and seconds on 6x 7seg LED display. When */
/* mins and secs are 00 00, contact closure for about */
/* 1 sec. */

/****** FUNCTION PROTOTYPES *****/
void setup(void);
void loop(void);

/***** DEFINITION OF DIGITAL OUTPUT PINS *****/
const uint8_t contactClosure_PIN_D7 = 7;

/***** DEFINITION OF Software Serial *****/
const uint8_t NEO_6M_GPS_module_PIN_SERIAL_TX_A0 = A0;
const uint8_t NEO_6M_GPS_module_PIN_SERIAL_RX_A1 = A1;
SoftwareSerial NEO_6M_GPS_module(NEO_6M_GPS_module_PIN_SERIAL_RX_A1, NEO_6M_GPS_module_PIN_SERIAL_TX_A0);

/***** DEFINITION OF I2C PINS *****/
const uint8_t lcd_LCD1602I2C_I2C_PIN_SDA_A4 = A4;
const uint8_t lcd_LCD1602I2C_I2C_PIN_SCL_A5 = A5;
const uint8_t lcd_LCD1602I2C_I2C_SLAVE_ADDRESS = 39;

/****** DEFINITION OF LIBRARIES CLASS INSTANCES*****/
MicroNMEA nmea;
LiquidCrystal_I2C lcd(lcd_LCD1602I2C_I2C_SLAVE_ADDRESS, 20, 4); // Initialize the LiquidCrystal_I2C object

void setup(void)
{
  // put your setup code here, to run once:

  pinMode(contactClosure_PIN_D7, OUTPUT);

  NEO_6M_GPS_module.begin(9600);

  // Initialize the LCD
  lcd.init();
  lcd.backlight();
  // Add additional setup code for System Requirement 1 here
}

void loop(void)
{
  // put your main code here, to run repeatedly:

  // Add code to read hour, minutes, and seconds from GPS module using MicroNMEA library
  // Uncomment and replace the placeholders with the actual code.
  //  int hours = nmea.getHours();
  //  int minutes = nmea.getMinutes();
  //  int seconds = nmea.getSeconds();

  // Display hours, minutes, and seconds on 6x 7seg LED display
  // Uncomment and replace the placeholders with the actual code.
  //  displaySevenSegment(hours);
  //  displaySevenSegment(minutes);
  //  displaySevenSegment(seconds);

  // Check if minutes and seconds are 00:00, if true, activate contact closure for about 1 second
  // Uncomment and replace the placeholders with the actual code.
  //  if (minutes == 0 && seconds == 0) {
  //    activateContactClosure();
  //  }

  delay(1000); // Delay for 1 second before the next iteration
}